Home > How To > Dock Post Driver

Dock Post Driver

Contents

the top of the tee had a screw on cap .... It is more volume of water not pressure that helps wash everything out. Roots can cause piles to seat off their desired location. That will be your "jet", providing a stream of water to wash and blow out a hole for the piling to set into. 5 Lay out the location of your pilings

The 4×4 should be pointed on the bottom. 1″ thick SteelĀ  on top and 3/16″ wall thickness on the sleeve. Can you find out what they used to sink others on your lake? Loading... This boat dock is the sturdiest thing I've ever laid eyes on.

How To Install Dock Posts In Water

We recently changed the size of the cap so it will now fit over a rough cut 4×4 post. Nothing serious but there is sway where the 8X8's don't have sway. v cap l l.__ l . __ hose l l l l l l Just slightly smaller scale of how the Golden Gate Bridge was made. When you do second post, put the brace on the other side at the bottom, when you get done you pull both over to create a x and that's it.

  1. I use alot of joist hangers and straps and i cross brace anything i can...
  2. Thanks." DJ D.
  3. wikiHow Contributor That depends on how much weight it is holding.
  4. Looks cool though.
  5. Thanks, Jaime Sponsored Links 05-14-09,03:50 AM #2 flopshot Member Join Date Nov 2005 Posts 948 the two basic methods are platfom mounted drivers (rams) or jetting in the post with water
  6. You can keep it against it until it's driven and then you just pull it over to the other post top and lag them together.
  7. it might be like rasslin a 'gator usually these guys have a small barge with an A-frame and a hoist you could also rig a gin-pole and hang the operation from
  8. unscrew the cap ....slide 4x4 down in side the PVC ....

I wonder if you could make a hole with a water hose inserted into a 4" pvc pipe. you're blowing out the muck with the pipe and water pressure and the post follows it down. Or, screw on threaded fittings to downsize the end. Dock Pilings Installation any experience PDA View Full Version : Air Powered Post Driver...

The post driver would probably be a rental item as well as I wouldn't have much use for once the boathouse went up. Driving Dock Pilings By Hand A crane can be built simply with a 24' pontoon boat, 2" steel water pipe, steel cable and a 12v car winch. and have shownothers how and most stick with my method... It's part of my new dock construction.

On the docks with and upper deck there is some side to side sway when your on top. Jetting Dock Pilings Is this a pond or lake? An alternative to the pump may be connecting to a fire hydrant, if your local utility will allow you to do so, but a back flow preventer must be used in SubscribeSubscribedUnsubscribe2020 Loading...

Driving Dock Pilings By Hand

G-man01-04-2005, 11:10 AMAll the docks in our development are 8x8 primarly for the look. connect the pump to the side part of the tee... How To Install Dock Posts In Water Sign in to report inappropriate content. How To Build A Simple Dock Here's how: get a giant C-clamp (or cut one in half and re-weld it to extend its opening), weld onto it some grippy angle-iron feet to bite into the wood, and

Sign in to add this to Watch Later Add to Loading playlists... Other suggestions would be appreciated. The dock where the boat lifts would one day be was done by a professional who had a pile driver on pontoons. It will sturdy up the job since you can't get them as deep as a pile driver and keep from screwing braces under water. How To Install Dock Pilings

That's my biggest concern with pipe. Add to Want to watch this again later? Maybe our newest member Bongo would like to offer his perspective like he did in the Stump Removal Thread. :purplaugh Dan K01-04-2005, 08:23 AMI have set a large number of 4 It's still available for water/marine use.

Go to a nearby sawmill and buy some white oak timbers that size they will cost about the same price and resist rot just as well. 4x4 Post Driver Transcript The interactive transcript could not be loaded. no reason to be exact...

thanks Reply Print this page Email this Message -A +A Flat listThreaded list Date - newest firstDate - oldest first 10 comments per page30 comments per page50 comments per page70 comments

Dudley Lamy 5,420 views 7:52 Pile Driving at Lake Anna - Duration: 9:58. Cancel Unsubscribe Working... The soil is somewhat sandy. How To Build A Stationary Dock driving 6x6" dock posts thru muck to bedrock?

Depending on the depth of the pile jetting, this will be a 6' to 12' section of 3/4" pipe with an elbow at one end to attach your pump discharge hose. Some of the posted I have set this way have been in for 5 years now and still look good and true. Looking at other docks, we have decided on either 6x6" or 6x4" posts, every 10 to 12 feet, 8' apart. IslandGirlTalk 38,364 views 5:19 DIY Dock Protector - Duration: 3:57.

bluemarlin View Public Profile Send a private message to bluemarlin Find all posts by bluemarlin #14 12-02-2013, 11:30 AM mattech Deranged Throat-Puncher Join Date: May 2008 Location: The outskirts The plan is to use 6'' x 6'' pt. I imagine $200-300. Find all posts by northgeorgiasportsman #10 12-02-2013, 08:33 AM BriarPatch99 Join Date: May 2010 Location: Nicholls, GA iTrader: (0) Check/Add Feedback I helped a follow worker put dock post

His parting words were scrub good now; or something like that. Artfuldodger View Public Profile Send a private message to Artfuldodger Find all posts by Artfuldodger #16 12-02-2013, 11:53 AM mattech Deranged Throat-Puncher Join Date: May 2008 Location: The outskirts Quail man View Public Profile Send a private message to Quail man Find all posts by Quail man #2 12-01-2013, 10:10 PM basstrkr Join Date: May 2007 Location: middle We welcome your comments and suggestions.

Do you have any trouble with water freezing & breaking the pipe?