Home > How To > Diy Reshaft Driver

Diy Reshaft Driver

Contents

Spine-align the shaft marking the NBP and the Spine on the masking tape. eHowSports 156,495 views 5:55 Golf Club Re-Shafting (Part 1) - Duration: 6:17. Just the clear coat and paint or you will weaken the shaft tip which could cause failure. Ebay ID:Treykook GolfWRX Likes : 6 10 Feedback Score Posted 18 May 2010 - 08:52 PM I'm good on the tip, so I'll shove that bad boy in (minus a ferrule

Some tools to clean out the hosels and prep them for reshafting. Joined: Aug 26, 2004 Messages: 2,734 Likes Received: 11 Trophy Points: 288 well at least i saved money on the shaft....maybe if they aren't busy they'll let me watch for awhile...cuz Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading... Just get them to pull the shaft for you. http://www.golfwrx.com/forums/topic/375542-driver-reshafting/

Reshafting A Driver Cost

This actually makes sense. You are using a theme designed for your browser. Back to top Remove This Advertisement Viewing As Guest GolfWRX Forums Advertisement Wanna get rid of this ugly yellow box? Rick Shiels Golf 229,640 views 11:40 How to extract a Taylormade adaptor - Duration: 4:18.

Last edited by Weirfan; Mar 12, 2009, 07:33 PM. "Don't cry because it's over, Smile because it happened " Comment Post Cancel Rickli8148 Low Handicapper Join Date: Apr 22, 2008 Posts: Put a ferrule in, it only takes 1 extra step to re-shaft that driver. I think Im going to try some kind of cord next time because they dont wear down fast. Golf Club Reshafting Instructions Sign in to add this video to a playlist.

Autoplay When autoplay is enabled, a suggested video will automatically play next. In this case, it'll be 1/8" below 38". golfperfect1 16,179 views 3:12 Loading more suggestions... Originally posted by Weirfan as for the tip prep, this is not a problematic area, all you are trying t o do is remove the shiney area ( paint) so the

I'm assuming a wire brush and sand paper, but I suppose that I could be wrong.You want a torch over a heat gun because the guns take much much longer to Reshafting Golf Clubs Cost As already mentioned, with a composite head you have to be extremely careful when you are heating the hosel or else you could loosen the bond between the graphite material and Dogfish Head posted Jun 15, 2017 CAVS should change a little !!! You will more than likely heat the shaft and the head too much and ruin them.

How To Remove A Shaft From A Driver

Sign in Statistics Add translations 26,911 views 11 Like this video? https://forum.mygolfspy.com/topic/8506-reshafting/ Loading... Reshafting A Driver Cost thepalmettogolfshop 23,787 views 4:57 How to extract a Taylormade adaptor - Duration: 4:18. Where To Reshaft Golf Clubs Im open to suggestions!

I'll have to find one. Slingblade61, Apr 16, 2006 #9 DrBrown Hack Numero Uno Joined: Sep 2, 2005 Messages: 153 Likes Received: 7 Trophy Points: 168 This place was charging me ~$34/club for fitting, grip and I thought R35 told me that but must have been someone else when I was trying to figure out how to do my Launcher Comp.Click to expand... Grexa Golf 53,657 views 5:56 How To extract Graphite or Steel Golf Shafts - Duration: 7:38. How To Reshaft Irons Youtube

RotarySwing.com Golf Instruction 242,103 views 8:15 How To Remove A Graphite Shaft From A Golf Club - Duration: 4:29. Sign in Transcript Statistics Add translations 163,954 views 120 Like this video? Additionally, you will need a heat source (heat gun or a mico flame torch are the most popular) and a shaf protector for the vice (cheap ones start around 3$.) Some Contact Us Help Home Top RSS Terms and Rules Privacy Policy Digital Point SearchForum software by XenForo™ ©2010-2017 XenForo Ltd.

Top Tue, 10/01/2006 - 14:52 #9 ajmooseman P.S PaulHas the delivery man been yet????? How To Install Taylormade Shaft Adapter and get the one you know will work. on the hosel?

I learned the hard way on the twisting the head on a graphite shafted driver and killed the shaft.

  1. They are designed to work with ferrules for proper shaft seating and epoxy curing strength.
  2. Fried Eggs Golf 134,201 views 6:39 Longest 'usable' golf club - Guinness World Records 2015 - Duration: 1:31.
  3. Take you hand and run it up and down the tape to make sure it's slippery everywhere.
  4. What do you use for epoxy?
  5. Welcome to our community forums, full of great people, ideas and excitement.
  6. GOLF GADGETS & APPAREL!
  7. He said that would put me a tad over a regular flex with the right kick.
  8. A long ruler or measuring device to measure club length and trim lengths.

Just be careful not to remove the outer layer of graphite. Start up your Propane Torch and put on your leather gloves. Loading... Driver Shafts Some will take up to 2, but it is usually the technique.

I can't believe Maxfli thinks a 3X stiff shaft should be used EVER. IMO, GT charges $10 to do it for you so I'd get it done there. put shaft back into hosel spin and wipe excess epoxy that spills over with solvent rag and set to dry in the playing position. also, does the fact that my clubhead is composite delicate the process any?

Please re-enable javascript to access full functionality. Make sure the tip goes all the way to the bottom of the bore depth in the hosel. prep the shaft? Seeing that this is your first attempt, you might want to avoid the 5min quick set epoxies.

Way too complicated. Repeat for all 360*. Comment Post Cancel Weirfan Tour Pro Join Date: Dec 9, 2005 Posts: 18519 #5 Mar 9, 2009, 01:47 PM Re: DIY: Reshafting your driver? Ebay ID:Treykook GolfWRX Likes : 6 10 Feedback Score Posted 21 May 2010 - 12:39 PM I just ordered some.

This way you can align the grip however you want without having to worry about allignning the shaft to match the correct grip postion when you are applying the epoxy in